h1

Rock Solid Kinect Mount (for Computer Vision)

April 24, 2012

The Kinect sensor does not come equipped with a tripod mounting screw. By now there are 8 million different ways to mount your Kinect to a tripod, your wall or the back of your TV. Unfortunately, they all mount to the bottom of the Kinect (beneath the tilt motor),  leaving the Kinect to jiggle and wiggle like it is listening to “Gettin’ Jiggy wit It.”

If you need the Kinect sensor to stay put, say to register it to another camera (e.g. DSLR) or a projector, then you need to get rid of the wiggle.

Our research group has come up with two methods to mount directly to the Kinect.

Disclaimer: Both of these methods involve modifying the Kinect.  You WILL do permanent and irrevocable damage to your Kinect if you continue down this path. We in no way claim that this is safe to yourself, others or your Kinect sensor.

Method 1: (developed by Kevin Karsch, implemented by Rajinder Sodhi)

This is the simplest, easiest and possibly recommended method.

Here we attach a tripod mount directly to the body of the Kinect (instead of the wiggly bottom) with adhesive. For the camera mount, you might be able to buy an adhesive camera mount such as:

EPIC Contoured Adhesive Mount

Kodak 1960806 Action Mount

We were in a time cruch, so we headed out to Radio Shack and bought a cheap tripod:

50″ 4-Section Tripod, Model: TV-1743

We then sawed off the top of the tripod, retrieving only the mount.

This was then glued with expoy directly to the base of the Kinect. Here we attached it to the top of the Kinect, in order to rigidly mount another camera on top. This process would also work to attach a tripod mount to the bottom of the Kinect.

Method 2: (developed by Brett Jones)

Here we use the existing screws holes of the Kinect to rigidly mount to a piece of plexiglass. This is definitely the most robust method, but also the most time consuming and costly (and dangerous?). You will need a sheet of plexiglass (acrylic), some screws, Torx security screwdrivers, a power drill and a power jigsaw. Do not proceed unless you are comfortable with power tools.

First we took off the motor and useless base for the Kinect. We followed the directions on iFixit, up to step 5. This requires purchasing a set of Torx (T6 & T10) security screwdrivers. Basically you remove the protective rubber pad on the base, then open the base using the T6 screwdriver.

We then just cut-off the plastic from the base using some metal clippers. Use scissors, a hacksaw, whatever you can find.

Now we will use the original screw holes to connect to an acryllic (plexiglass base).

Follow steps 6 & 7 on iFixit, to remove the bottom T10 security screws. We went to the local hardware store (Lowes) and bought some longer screws that fit the original holes. The thread count on the screws will not match perfectly, so this will most likely permanently damage the screw holes. (You won’t be able to put everything back together). I don’t remember the exact screws we bought, so just bring in one of the Kinect screws and find one that is the same diameter but longer in length (around 1.5 inches). You will also need matching nuts.

We also need a screw to attach to the tripod. So pick up a 1/4 inch screw that is 1-1.5 inches long with a matching nut.

We then need to cutout a piece of acrylic glass that will serve as a rigid body to attach to. We bought a 1/4 inch thick piece of acrylic glass at Lowes. We roughly measure the size of the Kinect and cut-out a rectangle of acrylic glass. Place the acrylic glass on the bottom on the Kinect and mark the locations of the 6 screw holes. Note where the cord comes out of the bottom on the Kinect. Also note where you would like to mount it to the tripod (taking the center of gravity of your camera-rig into account).

Now with a power drill (and all proper safety equipment) make 6 holes for the screws and one for the 1/4″ tripod screw. Then cutout a hole for the Kinect cord with a drill/jigsaw (it will have to big enough to thread the large USB end through).

Finally, insert the six screws, thread the cord through and screw them into the Kinect. Attach the 1/4″ screw for the tripod mount.

Whalla! Now you have a rock-solid Kinect mount.

Pro-tip: Check out 80/20 which sells a bunch of metal parts that connect with 1/4″ screws and are great for mounting cameras. They call themselves “An industrial erector set.”

Questions? Email me. I’ll update this post with more info.

Advertisements

One comment

  1. Thanks so much for sharing… hacking together a handheld kinect setup for 3d scanning experiments for feature film work, and found your writeup to be a great starting off place, much appreciated.



Leave a Reply

Fill in your details below or click an icon to log in:

WordPress.com Logo

You are commenting using your WordPress.com account. Log Out / Change )

Twitter picture

You are commenting using your Twitter account. Log Out / Change )

Facebook photo

You are commenting using your Facebook account. Log Out / Change )

Google+ photo

You are commenting using your Google+ account. Log Out / Change )

Connecting to %s

%d bloggers like this: